<tr id="b0rf1"><small id="b0rf1"></small></tr>
  • <tr id="b0rf1"></tr>

  • <ins id="b0rf1"><video id="b0rf1"><optgroup id="b0rf1"></optgroup></video></ins>

    1. <menuitem id="b0rf1"></menuitem>
      1. <output id="b0rf1"></output>
      2. <ins id="b0rf1"></ins>
        1. <tr id="b0rf1"></tr>
          <tr id="b0rf1"><nobr id="b0rf1"><delect id="b0rf1"></delect></nobr></tr>
          <ins id="b0rf1"></ins>

          <tr id="b0rf1"></tr>

          
          
          <mark id="b0rf1"></mark>
        2. <small id="b0rf1"></small>

            1. <small id="b0rf1"></small>
              1. <ins id="b0rf1"></ins>
                  聯系我們
                  聯系人:xx
                  轉讓電話:13313028229
                  地址:xx
                  新聞動態
                  鋼結構隔層的建造方法
                  由于水泥現澆很少人采用,所以我們重點說明槽鋼的搭法。下面的施工方法是以你的室內平面是方形的來考慮的。
                  Because cement cast-in-place is seldom used by people, we emphasize the way of channel steel. The following construction method is based on the square of your indoor plane.
                  1.槽鋼樓板的最關鍵一點就是槽鋼兩端的固定
                  1. the key point of channel steel floor is the fixed ends of channel steel.
                  固定方法主要有三種
                  There are three main types of fixed methods
                  一種是在墻上用角鋼做一個,并用膨脹螺絲鎖在墻上,然后用槽鋼固定在上面,也可以采用植筋的做法進行固定。此方法只限于兩端墻面是承重墻或者剛好有橫梁經過的地方,用膨脹螺絲固定于墻上,膨脹螺絲的間隔不超過200mm。
                  One is to make an angle steel on the wall, and use the expansion screw to lock it on the wall, then use the channel steel to fix it on top, and it can also be fixed by planting bar. This method is confined to the wall at both ends, or just with a beam passing through the wall. The expansion screw is fixed to the wall with the expansion screw, and the interval of the expansion screw is not more than 200mm.
                  二種是先在墻上打一個孔,然后把槽鋼伸進墻內,并由墻體直接承擔槽鋼的重量。此方法只限于承重墻或者較厚的剪力墻。
                  The two way is to first punch a hole on the wall, then extend the channel into the wall, and directly bear the weight of the channel steel. This method is limited to bearing walls or thicker shear walls.
                  三種方法是直接豎另一條槽鋼來支撐橫的槽鋼,豎的槽鋼要固定在墻上。此方法要考慮豎的槽鋼所處的位置的樓板的承重能力,宜多點分布式支撐,不要把力集中在少數的槽鋼上來承受。第三種做法要求采用槽鋼,而不是像第一種做法那樣用角鋼就行了。一般固定在最長的兩邊上面,如果最長的兩邊平行鋪設沒有固定條件時,也可以與最短的兩邊進行鋪設。
                  The three way is to directly erect another channel steel to support the horizontal channel steel, and the vertical channel steel must be fixed on the wall. This method should consider the load-bearing capacity of the floor in which the vertical channel steel is located, so that more support should be distributed, and the force should not be concentrated on a few channel steels. The third method requires channel steel instead of the angle steel used in the first practice. Generally fixed on the longest sides, if the longest two sides are laid in parallel without fixed conditions, they can also be laid on the shortest sides.
                  2.解決了槽鋼的固定點,下面要解決的就是主龍骨的編排
                  2. to solve the fixed point of channel steel, the next thing to be solved is the arrangement of the main keel.
                  一般對于居室來說,建議采用120×60×6mm或以上規格的槽鋼作用主龍骨。主龍骨應該與最短的一邊平行進行鋪設,間隔500mm左右。
                  Generally speaking, for the living room, it is recommended to use 120 x 60 x 6mm or above channel steel to act as the main keel. The main keel should be laid in parallel with the shortest side, about 500mm.
                  槽鋼必須架放在墻上的之上,且與墻面的空隙不超過10mm。槽鋼滿焊于橫檔之上。如果與最短的一邊平行鋪設沒有固定條件時,也可以與最長的一邊平行進行鋪設。
                  Channel steel must be placed above the wall, and the gap between the channel and the wall should not exceed 10mm. The channel steel is fully welded over the cross gear. If there is no fixed condition in parallel with the shortest side, it can also be laid in parallel with the longest side.
                  3.再在主龍骨之間焊設副龍骨
                  3. soldering the accessory keel between the main keel
                  副龍骨可采用等邊角鋼,規格采用50x50x4mm或以上的。
                  The side keel can be made of equilateral angle steel with 50x50x4mm or more specifications.
                  副龍骨滿焊于主龍骨之上,平面一致,并且與主龍骨橫向垂直,編排間隔建議值是300mm(最大值),宜密不宜疏。
                  The side keel is fully welded on the main keel, the plane is the same, and is perpendicular to the main keel, and the recommended interval is 300mm (maximum).
                  為安全起見,宜在副龍骨與主龍骨之間的下部再焊接一小段角鋼的邊角料,以策安全。
                  For safety reasons, it is advisable to weld a small angle steel leftover in the lower part between the keel and the main keel for safety.

                  北京鼎锘恒潤建筑裝飾有限公司

                  1. 電話:13313028229
                  2. 網址:www.www.auto632.com

                  版權北京建筑裝飾有限公司 網址:www.www.auto632.com 推薦:北京鋼結構加建閣樓制作,北京別墅加建改造公司,北京現澆混泥土澆筑公司,北京路面切割修復公司,北京樓頂防水堵漏公司,北京陽光房制作公司,北京混泥土切割拆除加固,北京現澆混凝土樓板制作公司,北京現澆樓梯公司

                   

                  亚洲女同成AV人片在线观看